The Concept And Production Process Of Soft Wall Bags

- May 31, 2018 -

Soft wall bags, as the name implies, use a wall decoration method that uses a flexible material to wrap the interior wall surface. In layman's terms, a soft pack is a piece of bulging stuff on a bedside background wall in some homes. Soft, such as leather or cotton, is a kind of soft interior soft decoration. The material it uses is soft in texture and soft in color, it can soften the overall space atmosphere, and its deep three-dimensional feeling can also enhance the home (www.021sofa.com) grade. In addition to beautifying the role of space, it is more important that it has the functions of sound absorption, sound insulation, moisture protection and collision avoidance. In the past, soft bags were mostly used in high-end hotels, clubs, KTVs, conference rooms and other places, and were rarely seen in ordinary home decoration. Now, some high-end residential real estate, villas and townhouses will also be used in large areas when they are renovated. More on the KTV. Not just the walls, the ceiling, some even in the corridors.

1. Process flow: Base or floor treatment → Hang straight, set squares, find rules, elastic line → Calculate materials, cut fabrics → Paste fabrics → Install stick or trim edges, brush trim paint → Soft wall principle On the floor of the room, the interior decoration of the ceiling has been basically completed, and the wall and the floor of the fine wooden decoration have been completed. When the surface decoration is started, the installation and installation of the soft wall decoration and the installation project are inserted.

 2. Grass-roots or floor treatment: Where the soft-decorative wall decoration of the room is mostly pre-embedded in the structural wall, the cement mortar leveling layer, and the brush spray cold base oil. Apply a felt and oil damp proof layer, install 50mm x 50mm wood wall ribs (medium distance is 450mm), and pave the top five plywood, as shown in Figure 9-25. This base layer or floor is actually the standard practice for this room. If the direct paving method is adopted, the grass-roots level must seriously deal with it. The method is to first grind the bottom plate with a grout and put it in a dense, full-scrape ~2 pass. After the putty is dried, it is smoothed with sandpaper and before the paste is applied on the surface of the base layer. Full brush oil (varnish + banana water) together. If there is a filling layer, this procedure can be simplified.

 3, hanging straight, set side, find rules, line: According to the requirements of the design drawings, the room needs soft wall decoration size, shape, etc. By hanging straight, sets of rules, find rules, bombs and other processes, the actual The size and shape of the design are implemented on the wall.

 4. Calculation of materials, sleeves, fillers, and fabrics: First, according to the requirements of the design drawings, determine the specific practices of the soft wall. There are two general approaches. One is the direct laying method (this method is relatively simple, but requires a higher level of flatness on the base or floor), and the second is the item-laying mosaic method. This method has a certain degree of difficulty. Horizontal and vertical, must not be skewed, dimensions must be accurate, etc. Placing a positioning mark is necessary to facilitate the registration. Then, according to the design requirements, the materials calculation and bottom village (filling materials) and fabric nesting work were performed. Note that the same room, the same pattern, and the fabric must be nested with the same roll of material and the same part (including fillers).

 5, paste the fabric: If you take the direct paving method construction, should be basically completed the wall fine wood decoration, border paint to meet the living conditions, can paste the fabric; If you take the prefabricated paving mosaic method, without this limitation, Paste fabric work in advance. First, according to the requirements of the design drawings and styling, paste the filler (such as foam, polystyrene board or mineral wool, wood strip, pentathronous board, etc.), and press the design materials (adhesive glue, nail, wood screw, and anodized aluminum cap). Head nails, copper wire, etc.) Fix the filler mat to the prefabricated tile-inlaid bottom plate, and then place the fabric up and down according to the positioning mark. The first part is to temporarily fix the upper part with a wooden bar and nails, and then put the lower end and the second one. After finding the side position, you can paste the fabric according to the design requirements.

 6, install the face or decorative sideline: According to the design choice and processing of a good face or decorative edge, according to the design requirements of the first paint brush (to meet the conditions of living), can be pre-fabricated mosaic decorative panels After the installation work, after the test has been completed to meet the design requirements and effects, it can be fixed and installed on the grass-roots level or on the decorative sideline.

 7, repair soft wall.


Related News

Related Products

  • Fabric Storage Bench With Golden Metal Cap
  • Fabric Storage Ottoman Bench Seat
  • Sofa Sleeper Multiple Colors
  • Pacific Loveseat Faux Leather Vinyl
  • Mesh Back Visitor Chair
  • 26 Inches Counter Height Barstool Gold